F2H-2 Banshee 3D Modeling Progress
Getting close to finishing the F2H-2 Banshee 3D modeling. This will be a complete 3D printed model kit. Progress was slowed as I got...
top of page
Search
Michael E Rieth
- Jan 26
- 1 min
Can't Fly Without Wings!
Not that it can fly. This will be a 3D printed static display scale model kit. More progress on the F2H-2 Banshee 3D model. The outer...
77 views0 comments
Michael E Rieth
- Jan 25
- 1 min
F2H-2 Banshee Work in Progress
I created the F2H-2 3D model first and then used that to make the F2H-3/4. I still need to finish the panel lines and after getting the...
77 views2 comments
Michael E Rieth
- Jul 28, 2023
- 1 min
3D SCANNING, 3D MODELING AND 3D PRINTING THE F2H-2 BANSHEE TO CORRECT THE KITTY HAWK KIT.
I have started 3D scanning, 3D modeling and 3D printing my custom model kits. I had created masters, poured molds and urethane resin...
109 views3 comments
Michael E Rieth
- Oct 7, 2020
- 1 min
3D Printed 1/48th Scale F2H-2N Banshee Nose
The 3D printed F2H-2N nose is glued on to the 1/48th scale Kitty Hawk Banshee model. I've been dialing in the 3D printing specs. There is...
288 views0 comments
Michael E Rieth
- May 31, 2019
- 2 min
F2H-2 Banshee on USS Essex Korean War Diorama
This photo was the inspiration for creating the diorama using the 1/48th scale Kitty Hawk F2H-2/2P Banshee with my Rieth Creations Resin...
898 views0 comments
Michael E Rieth
- Jan 9, 2019
- 1 min
Correcting Kitty Hawk F2H-2/2P Engine Exhaust
The exhaust cone and rear of the jet engine should have the same diameter. If gluing the flaps in the lowered position, you can see the...
458 views0 comments
Michael E Rieth
- Dec 20, 2018
- 1 min
Modifying the Kitty Hawk 1/48 Banshee Wing Folds to Glue the Outer Wings in the Down Position
I am making some modifications as I test build another Banshee to improve the fit of the resin to KH parts. I decided to do something...
505 views0 comments
Michael E Rieth
- Dec 12, 2018
- 1 min
Correcting the Kitty Hawk 1/48th Scale F2H-2/2P Banshee Nose Gear
The nose gear fork, B78, needs to be shortened. The square bottom of strut, B57, should be at the front curve of the fork. Parts C56 and...
349 views0 comments
Michael E Rieth
- Dec 11, 2018
- 1 min
ASSEMBLING THE F2H-2 BANSHEE NOSE GUN COMPARTMENT
If displaying the Banshee with the gun bay doors open and nose cone off, the nose gun bay needs to be modified to use the resin parts....
221 views0 comments
Michael E Rieth
- Dec 11, 2018
- 1 min
ASSEMBLING THE F2H-2 BANSHEE RESIN WING TO THE KH FUSELAGE. ENGRAVE NEW PANEL LINES.
REMINDER: Glue the KH cockpit, nose gear well, and part C62 to the KH fuselage. Glue the revised resin rear fuselage to the KH front...
437 views0 comments
Michael E Rieth
- Dec 11, 2018
- 2 min
ASSEMBLING THE F2H-2/2P BANSHEE RESIN EMPENNAGE (TAIL) TO KH FUSELAGE (REVISED)
I've revised where to cut the fuselage after feedback and I have made the rear fuselage a one piece hollow cast part. Gently scribe along...
274 views0 comments
Michael E Rieth
- Dec 11, 2018
- 1 min
ASSEMBLING THE F2H-2 RESIN CENTER WING
The upper and lower wings were cut from the casting sprue and some resin runner material was left to protect the edges and corners from...
479 views0 comments
Michael E Rieth
- Dec 11, 2018
- 1 min
ASSEMBLING THE F2H-2 BANSHEE JET ENGINES AND INTAKES
For easier fitting and gluing of the resin intakes to resin wing, it is advised that the jet engines be cut apart. Paint engine interior...
277 views0 comments
Michael E Rieth
- Sep 16, 2018
- 2 min
Kitty Hawk 1/48 F2H-2 Banshee Wing Tip Tanks…We’re Gluing Them on Wrong
While doing additional research for the Resin Correction Set, I was looking at the wing to tip tank area and realized that I had glued...
757 views0 comments
bottom of page